View CAT5113YI-10-GT3_3753300.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

? semiconductor components industries, llc, 2010 august, 2010 ? rev. 24 1 publication order number: cat5113/d cat5113 100-tap digitally program- mable potentiometer (dpp ) description the cat5113 is a single digitally programmable potentiometer (dpp ) designed as an electronic replacement for mechanical potentiometers. ideal for automated adjustments on high volume production lines, they are also well suited for applications where equipment requiring periodic adjustment is either difficult to access or located in a hazardous or remote environment. the cat5113 contains a 100 ? tap series resistor array connected between two terminals r h and r l . an up/down counter and decoder that are controlled by three input pins, determines which tap is connected to the wiper, r w . the wiper setting, stored in nonvolatile memory, is not lost when the device is powered down and is automatically reinstated when power is returned. the wiper can be adjusted to test new system values without affecting the stored setting. wiper ? control of the cat5113 is accomplished with three input control pins, cs , u/d , and inc . the inc input increments the wiper in the direction which is determined by the logic state of the u/d input. the cs input is used to select the device and also store the wiper position prior to power down. the digitally programmable potentiometer can be used as a three-terminal resistive divider or as a two-terminal variable resistor. features ? 100 ? position linear taper potentiometer ? non ? volatile eeprom wiper storage ? 10 na ultra ? low standby current ? single supply operation: 2.5 v ? 6.0 v ? increment up/down serial interface ? resistance values: 1 k , 10 k , 50 k and 100 k ? available in pdip, soic, tssop and msop packages ? these devices are pb ? free, halogen free/bfr free and are rohs compliant applications ? automated product calibration ? remote control adjustments ? offset, gain and zero control ? tamper ? proof calibrations ? contrast, brightness and volume controls ? motor controls and feedback systems ? programmable analog functions http://onsemi.com pin configurations r h r wb r l u/d inc v cc cs 1 see detailed ordering and shipping information in the package dimensions sect ion on page 13 of this data sheet. ordering information soic ? 8 v suffix case 751bd msop ? 8 z suffix case 846ad gnd pdip (l), soic (v), msop (z) pdip ? 8 l suffix case 646aa tssop ? 8 y suffix case 948al increment control inc up/down control u/d potentiometer high terminal r h ground gnd wiper terminal r w potentiometer low terminal r l function pin name pin function chip select cs supply voltage v cc tssop (y) (top views) gnd r h u/d inc r wb cs v cc r l 1
cat5113 http://onsemi.com 2 device marking information aarr = cat5113zi ? 10 ? t3 aarc = cat5113zi ? 50 ? t3 aarg = cat5113zi ? 00 ? t3 y = production year (last digit) m = production month (1 ? 9, a, b, c) p = product revision r = resistance: 0 = 1 k 2 = 10 k 4 = 50 k 5 = 100 k l = assembly location 4 = lead finish ? nipdau a = product revision (fixed as ?a?) cat5113l = device code (pdip) cat5113v = device code (soic) t = temperature range (industrial) y = production year (last digit) m = production month (1 ? 9, a, b, c) xxxx = last four digits of assembly lot number a3 = device code r = resistance: 2 = 10 k 4 = 50 k 5 = 100 k l = assembly location 4 = lead finish ? nipdau y = production year (last digit) m = production month (1 ? 9, a, b, c) xxx = last three digits of xxx = assembly lot number tssop pdip soic msop rl4a cat5113lt ymxxxx rl4a cat5113vt ymxxxx aarr ymp a3rl 4ymxxx
cat5113 http://onsemi.com 3 functional diagram figure 1. general control and memory power on gnd decoder 31 30 29 28 2 1 0 transfer gates resistor array 5 ? bit nonvolatile memory store and recall control circuitry 5 ? bit up/down counter gnd figure 2. detailed figure 3. electronic potentiometer implementation v cc cs inc u/d r h r w r l v cc recall cs inc u/d 1 of 32 r h r w r l r h r w r l pin description inc : increment control input the inc input moves the wiper in the up or down direction determined by the condition of the u/d input. u/d : up/down control input the u/d input controls the direction of the wiper movement. when in a high state and cs is low, any high ? to ? low transition on inc will cause the wiper to move one increment toward the r h terminal. when in a low state and cs is low, any high ? to ? low transition on inc will cause the wiper to move one increment towards the r l terminal. r h : high end potentiometer terminal r h is the high end terminal of the potentiometer. it is not required that this terminal be connected to a potential greater than the r l terminal. voltage applied to the r h terminal cannot exceed the supply voltage, v cc or go below ground, gnd. r w : wiper potentiometer terminal r w is the wiper terminal of the potentiometer. its position on the resistor array is controlled by the control inputs, inc , u/d and cs . voltage applied to the r w terminal cannot exceed the supply voltage, v cc or go below ground, gnd. r l : low end potentiometer terminal r l is the low end terminal of the potentiometer. it is not required that this terminal be connected to a potential less than the r h terminal. voltage applied to the r l terminal cannot exceed the supply voltage, v cc or go below ground, gnd. r l and r h are electrically interchangeable. cs : chip select the chip select input is used to activate the control input of the cat5113 and is active low. when in a high state, activity on the inc and u/d inputs will not affect or change the position of the wiper. device operation the cat5113 operates like a digitally controlled potentiometer with r h and r l equivalent to the high and low terminals and r w equivalent to the mechanical potentiometer?s wiper. there are 100 available tap positions including the resistor end points, r h and r l . there are 99 resistor elements connected in series between the r h and r l terminals. the wiper terminal is connected to one of the 100 taps and controlled by three inputs, inc , u/d and cs . these inputs control a seven ? bit up/down counter whose output is decoded to select the wiper position. the selected wiper position can be stored in nonvolatile memory using the inc and cs inputs. with cs set low the cat5113 is selected and will respond to the u/d and inc inputs. high to low transitions on inc will increment or decrement the wiper (depending on the state of the u/d input and seven ? bit counter). the wiper, when at either fixed terminal, acts like its mechanical equivalent and does not move beyond the last position. the value of the counter is stored in nonvolatile memory whenever cs transitions high while the inc input is also high. when the cat5113 is powered ? down, the last stored wiper counter position is maintained in the nonvolatile memory. when power is restored, the contents of the memory are recalled and the counter is set to the value stored. with inc set low, the cat5113 may be de ? selected and powered down without storing the current wiper position in nonvolatile memory. this allows the system to always power up to a preset value stored in nonvolatile memory.
cat5113 http://onsemi.com 4 table 1. operation modes inc cs u/d operation high to low low high wiper toward h high to low low low wiper toward l high low to high x store wiper position low low to high x no store, return to standby x high x standby table 2. absolute maximum ratings parameters ratings units supply voltage v cc to gnd ? 0.5 to +7 v inputs cs to gnd ? 0.5 to v cc +0.5 v inc to gnd ? 0.5 to v cc +0.5 v u/d to gnd ? 0.5 to v cc +0.5 v h to gnd ? 0.5 to v cc +0.5 v l to gnd ? 0.5 to v cc +0.5 v w to gnd ? 0.5 to v cc +0.5 v operating ambient temperature commercial (?c? or blank suffix) 0 to 70 c industrial (?i? suffix) ? 40 to +85 c junction temperature +150 c storage temperature ? 65 to 150 c lead soldering (10 s max) +300 c stresses exceeding maximum ratings may damage the device. maximum ratings are stress ratings only. functional operation above t he recommended operating conditions is not implied. extended exposure to stresses above the recommended operating conditions may af fect device reliability. table 3. reliability characteristics symbol parameter test method min typ max units v zap (note 1) esd susceptibility mil ? std ? 883, test method 3015 2000 v i lth (notes 1, 2) latch ? up jedec standard 17 100 ma t dr data retention mil ? std ? 883, test method 1008 100 years n end endurance mil ? std ? 883, test method 1003 1,000,000 stores 1. this parameter is tested initially and after a design or process change that affects the parameter. 2. latch ? up protection is provided for stresses up to 100 ma on address and data pins from ? 1 v to v cc + 1 v
cat5113 http://onsemi.com 5 table 4. dc electrical characteristics (v cc = +2.5 v to +6 v unless otherwise specified) symbol parameter conditions min typ max units power supply v cc operating voltage range 2.5 ? 6.0 v i cc1 supply current (increment) v cc = 6 v, f = 1 mhz, i w = 0 ? ? 100 a v cc = 6 v, f = 250 khz, i w = 0 ? ? 50 a i cc2 supply current (write) programming, v cc = 6 v ? ? 1000 a v cc = 3 v ? ? 500 a i sb1 (note 3) supply current (standby) cs = v cc ? 0.3 v u/d , inc = v cc ? 0.3 v or gnd ? 0.01 1 a logic inputs i ih input leakage current v in = v cc ? ? 10 a i il input leakage current v in = 0 v ? ? ? 10 a v ih2 cmos high level input voltage 2.5 v v cc 6 v v cc x 0.7 ? v cc + 0.3 v v il2 cmos low level input voltage ? 0.3 ? v cc x 0.2 v potentiometer characteristics r pot potentiometer resistance ? 01 device 1 k ? 10 device 10 ? 50 device 50 ? 00 device 100 pot. resistance tolerance 20 % v rh voltage on r h pin 0 v cc v v rl voltage on r l pin 0 v cc v resolution 1 % inl integral linearity error i w 2 a 0.5 1 lsb dnl differential linearity error i w 2 a 0.25 0.5 lsb r wi wiper resistance v cc = 5 v, i w = 1 ma 400 v cc = 2.5 v, i w = 1 ma 1000 i w wiper current (note 4) ? 4.4 4.4 ma tc rpot tc of pot resistance 300 ppm/ c tc ratio ratiometric tc 20 ppm/ c v n noise 100 khz / 1 khz 8/24 nv/ hz c h /c l /c w potentiometer capacitances 8/8/25 pf fc frequency response passive attenuator, 10 k 1.7 mhz 3. latch ? up protection is provided for stresses up to 100 ma on address and data pins from ? 1 v to v cc + 1 v 4. this parameter is not 100% tested.
cat5113 http://onsemi.com 6 table 5. ac test conditions v cc range 2.5 v v cc 6 v input pulse levels 0.2 v cc to 0.7 v cc input rise and fall times 10 ns input reference levels 0.5 v cc table 6. ac operating characteristics (v cc = +2.5 v to +6.0 v, v h = v cc , v l = 0 v, unless otherwise specified) symbol parameter min typ (note 5) max units t ci cs to inc setup 100 ? ? ns t di u/d to inc setup 50 ? ? ns t id u/d to inc hold 100 ? ? ns t il inc low period 250 ? ? ns t ih inc high period 250 ? ? ns t ic inc inactive to cs inactive 1 ? ? s t cph cs deselect time (no store) 100 ? ? ns t cph cs deselect time (store) 10 ? ? ms t iw inc to v out change ? 1 5 s t cyc inc cycle time 1 ? ? s t r , t f (note 6) inc input rise and fall time ? ? 500 s t pu (note 6) power ? up to wiper stable ? ? 1 ms t wr store cycle ? 5 10 ms 5. typical values are for t a = 25 c and nominal supply voltage. 6. this parameter is periodically sampled and not 100% tested. 7. mi in the a.c. timing diagram refers to the minimum incremental change in the w output due to a change in the wiper position. figure 4. a.c. timing 90% 90% 10% (store) t r t f mi (3) t ic t cph t iw r w u/d inc cs t ci t di t id t il t ih t cyc
cat5113 http://onsemi.com 7 applications information (a) resistive divider (b) variable resistance (c) two ? port figure 5. potentiometer configuration applications figure 6. programmable instrumentation amplifier +5 v +2.5 v 2 8 3 2 6 5 7 9 4 10 11 8 1 1 7 4 + ? + ? + ? +5 v cat5113/5114 dpp figure 7. programmable sq. wave oscillator (555) figure 8. sensor auto referencing circuit +5 v ? 5 v 4 11 1 499 k ic1b ic1a 20 k 499 k 2 3 6 5 499 k 499 k 10 k 0.01 f osc ic3a 1 / 4 74hc132 + ? + ? sensor 2 8 1 7 7 4 +5 v +200 mv cat5111/5112 ic2 dpp + ? +5 v 0.01 f 0.01 f 0.003 f c 5 3 6 7 8 4 1 2 65 3 2 8 1 7 4 +5 v dpp 555 r 2 r 2 r 1 r 3 r 4 r 4 v 1 ( ? ) v 2 (+) v o a 3 a 1 = a 2 = a 3 = 1 / 4 lm6064 r 2 = r 3 = r 4 = 5 k r pot = 10 k r b r 2 r a r 1 pr pot (1 ? p)r pot cs v sensor = 1 v 50 mv v out = 1 v 1 mv v ref = 1 v v corr r 3
cat5113 http://onsemi.com 8 figure 9. programmable voltage regulator 0.1 f 1 f 6.8 f 11 k 100 k 1.23 v 2 8 1 7 4 5 3 6 +5 v dpp 2952 cat5113/5114 fb sd gnd figure 10. programmable i to v converter +2.5 v +5 v 2 7 3 3 5 4 6 6 + ? lt1097 +5 v 2 7 3 4 6 + ? 2 8 1 7 4 +5 v cat5113/5114 dpp pr (1 ? p)r 330 330 1 m 10 k +5 v +5 v +2.5 v +5 v ic3 cat5111/5112 clo ic1 393 ai ic4 2 3 + ? 1 2 8 1 7 4 +5 v osc ic2 74hc132 0.1 f + ? chi 6 5 5 6 3 + ? 7 dpp figure 11. automatic gain control +5 v r3 r2 r1 0.001 f 0.001 f 1 f 2 7 3 4 6 + ? 2 8 1 7 4 +5 v cat5113/5114 dpp +2.5 v figure 12. programmable bandpass filter figure 13. programmable current source/sink cat5111/5112 +5 v +5 v serial bus +2.5 v +2.5 v +5 v 2 4 7 5 6 311 1 + ? + ? r + ? 2.5 k r 1 100 k r 1 100 k r 1 100 k r 1 100 k v s v out v o (reg) r 1 r 2 820 r 3 10 k v in (unreg) shutdown i s a 1 a 2 v o v o 0 v o 2.5 v v ul v ll r 1 r 3 r 2 10 k v s 0 v s 2.5 v 10 k c 1 c 2 v o v s 10 k 100 k a 1 50 k i s a 2 a 1 = a 2 = lmc6064a
cat5113 http://onsemi.com 9 package dimensions pdip ? 8, 300 mils case 646aa ? 01 issue a e1 d a l eb b2 a1 a2 e eb c top view side view end view pin # 1 identification notes: (1) all dimensions are in millimeters. (2) complies with jedec ms-001. symbol min nom max a a1 a2 b b2 c d e e1 l 0.38 2.92 0.36 6.10 1.14 0.20 9.02 2.54 bsc 3.30 5.33 4.95 0.56 7.11 1.78 0.36 10.16 eb 7.87 10.92 e 7.62 8.25 2.92 3.80 3.30 0.46 6.35 1.52 0.25 9.27 7.87
cat5113 http://onsemi.com 10 package dimensions soic 8, 150 mils case 751bd ? 01 issue o e1 e a a1 h l c e b d pin # 1 identification top view side view end view notes: (1) all dimensions are in millimeters. angles in degrees. (2) complies with jedec ms-012. symbol min nom max a a1 b c d e e1 e h 0o 8o 0.10 0.33 0.19 0.25 4.80 5.80 3.80 1.27 bsc 1.75 0.25 0.51 0.25 0.50 5.00 6.20 4.00 l 0.40 1.27 1.35
cat5113 http://onsemi.com 11 package dimensions tssop8, 4.4x3 case 948al ? 01 issue o e1 e a2 a1 e b d c a top view side view end view 1 l1 l notes: (1) all dimensions are in millimeters. angles in degrees. (2) complies with jedec mo-153. symbol min nom max a a1 a2 b c d e e1 e l1 0o 8o l 0.05 0.80 0.19 0.09 0.50 2.90 6.30 4.30 0.65 bsc 1.00 ref 1.20 0.15 1.05 0.30 0.20 0.75 3.10 6.50 4.50 0.90 0.60 3.00 6.40 4.40
cat5113 http://onsemi.com 12 package dimensions msop 8, 3x3 case 846ad ? 01 issue o e1 e a2 a1 e b d c a top view side view end view l1 l2 l detail a detail a notes: (1) all dimensions are in millimeters. angles in degrees. (2) complies with jedec mo-187. symbol min nom max a a1 a2 b c d e e1 e l 0o 6o l2 0.05 0.75 0.22 0.13 0.40 2.90 4.80 2.90 0.65 bsc 0.25 bsc 1.10 0.15 0.95 0.38 0.23 0.80 3.10 5.00 3.10 0.60 3.00 4.90 3.00 l1 0.95 ref 0.10 0.85
cat5113 http://onsemi.com 13 example of ordering information (note 11) prefix device # suffix company id cat 5113 v product number 5113 i ? gt3 package i = industrial ( ? 40 c to +85 c) temperature range l: pdip v: soic y: tssop z: msop g: nipdau blank: matte ? tin t: tape & reel 3: 3,000 units / reel tape & reel (note 12) (optional) ? 10 resistance ? 01: 1 k ? 10: 10 k ? 50: 50 k ? 00: 100 k lead finish (notes 9, 10) table 7. ordering information orderable part number resistance (k ) package ? pins lead finish cat5113li ? 01 ? g 1 pdip ? 8 nipdau cat5113li ? 10 ? g 10 cat5113li ? 50 ? g 50 cat5113li ? 00 ? g 100 cat5113vi ? 01 ? gt3 1 soic ? 8 nipdau cat5113vi ? 10 ? gt3 10 cat5113vi ? 50 ? gt3 50 cat5113vi ? 00 ? gt3 100 cat5113yi ? 01 ? gt3 1 tssop ? 8 nipdau cat5113yi ? 10 ? gt3 10 cat5113yi ? 50 ? gt3 50 cat5113yi ? 00 ? gt3 100 cat5113zi ? 01 ? t3 1 msop ? 8 matte ? tin cat5113zi ? 10 ? t3 10 cat5113zi ? 50 ? t3 50 cat5113zi ? 00 ? t3 100 8. all packages are rohs ? compliant (lead ? free, halogen ? free). 9. the standard lead finish is nipdau, except msop package is matte ? tin. 10. contact factory for matte ? tin finish availability for pdip, soic and tssop packages. 11. the device used in the above example is a cat5113vi ? 10 ? gt3 (soic, industrial temperature, 10 k , nipdau, tape & reel, 3,000/reel). 12. for information on tape and reel specifications, including part orientation and tape sizes, please refer to our tape and ree l packaging specifications brochure, brd8011/d. on semiconductor and are registered trademarks of semiconductor components industries, llc (scillc). scillc reserves the right to mak e changes without further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for an y particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including wi thout limitation special, consequential or incidental damages. ?typical? parameters which may be provided in scillc data sheets and/or specifications can and do vary in different application s and actual performance may vary over time. all operating parameters, including ?typicals? must be validated for each customer application by customer?s technical experts. scillc does not convey any license under its patent rights nor the rights of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the scillc product could create a sit uation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer shall indemnify and hold scillc and its of ficers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, direct ly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that scillc was negligent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyright laws and is not for resale in any manner. cat5113/d dpp is a trademark of semiconductor components industries, llc. publication ordering information n. american technical support : 800 ? 282 ? 9855 toll free usa/canada europe, middle east and africa technical support: phone: 421 33 790 2910 japan customer focus center phone: 81 ? 3 ? 5773 ? 3850 literature fulfillment : literature distribution center for on semiconductor p.o. box 5163, denver, colorado 80217 usa phone : 303 ? 675 ? 2175 or 800 ? 344 ? 3860 toll free usa/canada fax : 303 ? 675 ? 2176 or 800 ? 344 ? 3867 toll free usa/canada email : orderlit@onsemi.com on semiconductor website : www.onsemi.com order literature : http://www.onsemi.com/orderlit for additional information, please contact your local sales representative

▲Up To Search▲

Price & Availability of CAT5113YI-10-GT3

	To Download CAT5113YI-10-GT3 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .